ZUMAFORUMS.NET
http://www.zumaforums.net/phpBB3/

17.5 dellorto parts needed. Suggestions
http://www.zumaforums.net/phpBB3/viewtopic.php?f=23&t=26465
Page 1 of 1

Author:  TEC3 [ Sat Jan 31, 2015 4:26 pm ]
Post subject:  17.5 dellorto parts needed. Suggestions

Scored a really clean dellorto 17.5 for my prebug from a zuma forum member. A few on here suggested to get a bigger carb than my 14mm.

I need to get a top cap, needle slide, and needle.

Where is the best place to order these and what should I be looking for?

Thanks,

Tommy

Author:  FScott [ Sat Jan 31, 2015 4:36 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

Treatland.tv is great.

Author:  TEC3 [ Sat Jan 31, 2015 5:08 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

For some reason I can't seem to find those parts, just whole carbs. I probably am just sucking at the internet

Author:  Nick Batzdorf [ Sat Jan 31, 2015 9:06 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

They may not have the top. Try Dellortodirect.com - but ask them for better shipping than their website generates.

Author:  TEC3 [ Sat Jan 31, 2015 9:18 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

So I found options, what size needle and slide do I need? Will these top caps work?

out

https://www.treatland.tv/SearchResults. ... bg+top+cap
https://www.treatland.tv/SearchResults. ... phbg+slide
https://www.treatland.tv/SearchResults. ... hbg+needle

Author:  FScott [ Sat Jan 31, 2015 11:35 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

No idea what your build is. Gotta fill out sig line.

Generally you're looking at a W7 needle and a 40 slide to start.

Author:  FScott [ Sat Jan 31, 2015 11:38 pm ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

And can't help with the top selection without more info. You got the DS/Racing PHBG?

Author:  Pig [ Sun Feb 01, 2015 12:21 am ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

With the 17.5 Dell I've always used an A12 needle. Have a look at my sig line for my prebug, it should get you close. But then again I have know idea what your set up is. Fill in your sig line!

Author:  specalk [ Sun Feb 01, 2015 6:06 am ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

I'll sell you a needle kit for that carb

Author:  TEC3 [ Sun Feb 01, 2015 6:27 am ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

Sorry guys, should have posted that originally.

89 prebug
70cc BBK
NCY 3shoe clutch, yellow springs
Stock contra spring
Arrow exhaust kit
Stock variator with new rollers going in from the exhaust kit.
Open air filter with plastic cover.
Old/ current carb. TK 14mm stock 05 zuma carb

New carb dellorto 17.5mm PHVA missing top, slide and needle

Author:  TEC3 [ Sun Feb 01, 2015 6:28 am ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

Special K, I would be interested if you have the setup I would need.

Author:  TEC3 [ Sun Feb 01, 2015 7:33 am ]
Post subject:  Re: 17.5 dellorto parts needed. Suggestions

So he told me it was a PHGB, but it is actually a PHVA TS.

I can find needles on treats as well as top caps. Not sure if I need version 1 or 2 yet but will figure that out.

I cannot find a slide though for the PHVA TS. Any help with finding that? I can fun only for the ED version.

Page 1 of 1 All times are UTC - 7 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/